Ar Maglock Reviews

Here are the steps to install the AR MAGLOCK on your rifle:

1. Remove the existing magazine release button, using a pick tool, a screwdriver or a bullet button tool depending on the type of button.
2. Insert the ARMagLock spring and stand off into the magazine release button hole and tighten the cap screw with an allen wrench, aligning the top lip with the upper receiver.
3. Remove the rear takedown pin by pushing it slightly, using a pick tool to push the detent pin back, and using a flat head screwdriver to push the detent pin out from the left side.
4. Insert the custom-made takedown pin provided by ARMagLock and push the detent pin back in.
5. Perform a function test to check the ARMagLock is working properly.

Please note that these instructions are for general guidance and may vary depending on the specific model of your rifle and the version of the AR MAGLOCK you are installing. Always refer to the manufacturer's instructions for the most accurate information.

The website armaglock.com offers a variety of products. The AR MAGLOCK AR-15 (.223 / 5.56) – Gen 1 is priced between $31.45 and $92.45. The AR MAGLOCK AR-10 (.308) – Gen 1 is priced between $31.45 and $35.45. The AR MAGLOCK AR-15 (.223 / 5.56) – Gen 2 is priced between $40.45 and $101.45. The AR MAGLOCK AR-15 (.223 / 5.56) – Gen 3 is priced between $44.95 and $105.95. The AR MAGLOCK AR-15 (.223 / 5.56) – Gen 4 is priced between $49.95 and $110.95. They also offer discounts on multiple purchases. For example, if you purchase any 2 locking kits, you get 20% off. If you purchase any 3 locking kits, you get 25% off. If you purchase any 4 or more locking kits, you get 30% off.

The AR MAGLOCK is a device that turns your firearm into a "fixed magazine" firearm. It prevents the release of the magazine unless you pull the takedown pin and separate the upper and lower receivers, thus "disassembling" the firearm action. Once the receivers are minimally separated, the AR MAGLOCK can be engaged to release the magazine. This device is used for compliance in states like California, Illinois, New York, and others. The AR MAGLOCK allows the shooter to re-insert a magazine while the upper and lowers receivers (the action) are closed or open, allowing for significantly faster magazine changes. Some versions of the AR MAGLOCK, like the Gen 4, come with a set screw on the locking arm, allowing for adjustment to any receiver width including billet, composite, or 80% non-mil-spec receivers. It also allows for "free state" adjustment when traveling outside California. Just reset the set screw to the end of the post and the locking arm will work just like an OEM magazine release button. The Gen 4 and KingPin combo allows for minimal separation (action disassembly) of the upper and lower receivers. The new KingPin holds the upper receiver from flying open when disassembling the action. Just a simple push on the pin with your thumb opens the action for mag changes, then automatically re-locks when you push the receivers together.

AR Maglock is a company that specializes in fixed magazine lock and release solutions for firearms. They offer a variety of products, including the AR MAGLOCK AR-15 (.223 / 5.56) – Gen 1, AR MAGLOCK AR-10 (.308) – Gen 1, AR MAGLOCK AR-15 (.223 / 5.56) – Gen 2, and AR MAGLOCK AR-15 (.223 / 5.56) – Gen 3. These products are designed for compliance in states like California, Illinois, New York, and others. They also offer discounts for purchasing multiple locking kits. Notably, Daniel Defense chooses AR MAGLOCK as their only vendor for supplying fixed magazine solutions on their rifles coming into California. The company also offers a Gen 4 Magazine Lock with a KingPin combo that allows for minimal separation of the upper and lower receivers. The new KingPin holds the upper receiver from flying open when disassembling the action. All AR MAGLOCK locking kits are patented. The company also provides instructional videos on how to install and operate their products.

Here are the steps to install AR MAGLOCK products:

1. Place the provided spring onto the AR Maglock standoff.
2. Insert the AR Maglock with spring into the magazine button well.
3. Tighten the cap screw on firmly but do not tighten it all the way.
4. Align the top lip of the AR Maglock so that it is flush with the upper receiver.

For Gen 4 MAGLOCK device on an AR-10 rifle, follow these instructions:

1. Remove the existing magazine release button, using a pick tool, a screwdriver or a bullet button tool depending on the type of button.
2. Insert the ARMagLock spring and stand off into the magazine release button hole and tighten the cap screw with an allen wrench, aligning the top lip with the upper receiver.
3. Remove the rear takedown pin by pushing it slightly, using a pick tool to push the detent pin back, and using a flat head screwdriver to push the detent pin out from the left side.
4. Insert the custom-made takedown pin provided by ARMagLock and push the detent pin back in.
5. Perform a function test to check the ARMagLock is working properly.

For MAGLOCK King Pin, follow these instructions:

1. The King Pin allows you to separate an AR-15 upper and lower receiver by a quarter inch, enough to allow the MAGLOCK to release the magazine, but preventing the upper from flopping forward on the front takedown pin.

Please note that these are general instructions and may vary depending on the specific product and model. Always refer to the product manual for detailed instructions.

You can contact the customer support at armaglock.com by sending an email to info@armaglock.com. They also have a Contact page and a Support page on their website where you might find additional information.

The Return & Refund Policy of armaglock.com states that from March 3rd, 2021 until further notice, all sales are FINAL. There are No cancellations and NO RETURNS. No exceptions. After 3/3/21, all PayPal refund requests will be disputed to the fullest extent. All products sold by them are new and under warranty from the manufacturer, unless otherwise stated in the product description. Shipping & handling, insurance, processing fees are NOT refundable. Only the Product purchase price will be refunded minus any applicable restocking fees. The customer is responsible for return shipping charges unless the return is due to their error of order processing.

As for the Shipping Policy, due to heavy demand from end consumers, EOM’s and dealers, please allow up to 10 business days for your product to be delivered as they have a high volume of sales at all times due to the demand for their product. The customer is responsible for return shipping charges unless the return is due to their error of order processing.

Armaglock.com is the website for AR Maglock, a company that sells fixed magazine lock and release kits for AR-15 and AR-10 rifles. These kits are designed to help gun owners comply with state laws in places like California, Illinois, and New York, where regulations around assault weapons are strict. The AR Maglock turns a firearm into a "fixed magazine" firearm, meaning the magazine cannot be released unless the firearm is disassembled. This allows gun owners to avoid registering their firearms as assault weapons. The company also offers discounts for purchasing multiple locking kits. They have a range of products, including the AR MAGLOCK AR-15 (.223 / 5.56) – Gen 1, Gen 2, and Gen 3, and the AR MAGLOCK AR-10 (.308) – Gen 1. The website also provides information about relevant laws and regulations.

You can contact the customer service at armaglock.com by sending an email to info@armaglock.com. They also have a Contact page on their website where you might find additional ways to get in touch with them. If you have any issues with their products, you can refer to the Support page on their website for troubleshooting guides and installation instructions. Remember to always use the products as designed and intended for use. If you need further assistance, please let me know.